3 angled DSP cards are so easy and can vary with your imagination! Take a Basic White cardstock base and three sheets of cardstock and DSP and you have the makings of a quick and easy card that can vary as far as your willing to test it!
Measurements:
Thick White Cardstock (3) 4 1/4″ x 11″
scored at 5 1/2″
Basic White cardstock (1) 4″ x 5 1/4″
Dandy Designs (2) 4″ x 5 1/4″
scraps of White and a coordinating colored
cardstock
Take the 3 pieces of 4″ x 5 1/4″ pieces of paper
– make sure that the two pieces of DSP coordinate and different designs are facing upwards.
Make the first angled cut anywhere on the left side of the 5 1/4″ side and angle it into the bottom right hand corner.
Starting at the top right hand corner angle the paper to the desired angle and starting in the middle of the paper cut down to the edge of the paper and then reverse to the upper corner (do not start the cut at the point of the corner as you can crumple the corner edge)
You will now have three pieces of each type of paper.
Measurements:
Thick White Cardstock (3) 4 1/4″ x 11″
scored at 5 1/2″
Basic White cardstock (1) 4″ x 5 1/4″
Dandy Designs (2) 4″ x 5 1/4″
scraps of White and a coordinating colored
cardstock
Take the 3 pieces of 4″ x 5 1/4″ pieces of paper
– make sure that the two pieces of DSP coordinate and different designs are facing upwards.
Make the first angled cut anywhere on the left side of the 5 1/4″ side and angle it into the bottom right hand corner.
Starting at the top right hand corner angle the paper to the desired angle and starting in the middle of the paper cut down to the edge of the paper and then reverse to the upper corner (do not start the cut at the point of the corner as you can crumple the corner edge)
You will now have three pieces of each type of paper.
Take the White cardstock and run it through a 3D Embossing Folder of your choice for a little depth and dimension. I used the Timeworn Type.
The angled cuts will match exactly because you cut them at the same time.
Alternate the three different pieces and get the base for three different cards!
Adhere the left corner piece to the matching corner of the card base.
Make sure to get the tape to the edges of each of the separate sections and adhere the top right hand corner piece to the card.
Adhere the bottom piece to the card base.
Die cut a matte out of coordinating colored cardstock (I choose Balmy Blue) and I die cut with the Layering Circles dies. Cut a smaller Basic White cardstock to fit inside the matte (I used the Stylish Shapes) Stamp an image and color with Stampin’ Blends. I used the Adorable Owls Sale-a-bration set and use the Bronze and Ivory blends and the Light Balmy Blue.
Adhere the stamped circle to the Balmy Blue matte and pop up the Owl on Stampin’ Dimensionals. Place White Glittered Organdy ribbon behind the popped up circle and adhere to the card where the three papers converge.
Add the new Pastel Adhesive-Backed Sequins to the card and a sentiment in Tuxedo Black Memento ink to the lower right hand side and so cute you are done!
Try this with some of your own DSP or better yet put in an order and get some FREE Designer Series Paper out of the 2023 Sale-a-bration catalog.
The current hostess code is SWXBZUH9 and go out and create some art of your very own – one stamp at a time!
Try this with some of your own DSP or better yet put in an order and get some FREE Designer Series Paper out of the 2023 Sale-a-bration catalog.
The current hostess code is SWXBZUH9 and go out and create some art of your very own – one stamp at a time!
Happy Stampin’
Natalie
Here are some other samples created using the 3 angled technique!
Product List
