tri panel slider card with thoughtful journey dsp

tri panel slider card with thoughtful journey dsp

Looking for an easy and fun interactive stand up card that will WOW those you send this too – then look no farther tan the tri-panel slider card!
The new Thoughtful Journey 6″ x 6″ DSP is exquisite and this is a perfect card to showcase a large portion of it!

Measurements:
BASE: Misty Moonlight 4 1/4″ x 9 1/2″
scored at 1″, 2″, 7 1/2″ and 8 1/2″
Night of Navy CS (2) 1 1/4″ x 5 1/2″
(1) 1 3/4″ x 5 1/2″
DSP 3 1/2″ x 5 1/4″ cut into three sections
1″, 1 1/2″ and 1″ keep in consecutive order
Basic White CS 4″ x 5 1/4″ (optional for the
inside) scraps for die cut and circle die

Score the Base cardstock at 1″, 2″ 7 1/2″ and 8 1/2″ on the long side of the cardstock. Score a mountain fold at 1″ valley fold at 2″ and 7 1/2″ and another mountain fold at 8 1/2″.
Mount the Designer Series Paper on the Night of navy matte pieces the 1″ pieces on the (2) 1 1/4″ pieces of matte cardstock and the 1 1/2″ piece on the 1 3/4″ matte.
Adhere the last one inch of the matte to the top edge of the right hand side panel.
Adhere the last one inch of the larger matte to the middle of the left matte. The easiest way to do this is to push the outside panels inward to close them and lay the top panel over the left edge of the card then match the edges of the middle piece below the top panel making sure that it is straight and adhere to the left hand edge of the card.
Adhere the last smaller matte piece to the right side panel edge placing glue or tape only on the last one inch of the matted piece. It is easiest to adhere while the card is closed matching up the edges of the middle piece right above this bottom piece you are adhering to the card.
Die cut one of the circles from the Spotlight on Nature dies and stamp in Misty Moonlight one of the sentiments from the Thoughtful Wishes stamp set. Adhere to the top panel.
Die cut the larger leaves die from the Thoughtful Wishes die set and position it under the sentiment circle and adhere in the desired position to the middle panel only.
I added embellishments to the sentiment die around the sentiment to finish off this WOW slider card! It is very cool how this card stands for display!

Try this today with some of your own scenic DSP it is a great way to show off pretty papers. Now go and create some art work of your very own own lovely stamp at a time!

Happy Stampin’
Natalie

triple slider card

triple slider card

A Triple Slider Fun Fold card is a fun way to show off the pretty On the Horizons DSP (#157768).

Measurements:

Blackberry Bliss CS 5 1/4″ x 11″
scored at 1 3/4″ and 3 1/2″ rotate 180
degrees and score again at 1 3/4″ and 3 1/2″
Sentiment matte 1 1/2″ x 2″
Fresh Freesia (1) 4 1/4″ x 5 1/2″
(1) 3″ square
Basic White CS (1) 3 3/4″ x 5″
(1) 2 3/4″ square
(1) 1 1/4″ x 1 3/4″
Designer Series Paper 3 3/4″ x 4 7/8″ cut into
three pieces 3 3/4″ x 1 5/8″

Score and burnish the four score lines on the base card. See photo below.
Add two lines of tape in the upper left corner – see pictures below)
Add one of the 3 3/4″ x 1 5/8″ on the top corner and then add tape to the bottom left on the same side as the top slider.
Place the two opposing sides together and there will be an open spot on the right panel and add adhesive.
Add the third 3 3/4″ x 1 5/8″ piece to the middle in between the top and bottom pieces.
Add the Basic White 3 3/4″ x 5″ to the middle base of the card.
Add adhesive to the back of the card base. Then add to the center of the Fresh Freesia 4 1/4″ x 5 1/2″ layer.
When cutting the Designer Series Paper – keep in order. Add the middle DSP piece in the center of the middle slider.
Add the top piece of DSP to the top slider but position it closer to the bottom of the Blackberry Bliss cardstock piece. even on the top and sides but closer to the middle piece of DSP than perfectly centered.
Add the last bottom piece of DSP closer to the top of the bottom slider cardstock – even on the sides and bottom but positioned closer to the middle piece of DSP.
stamp the sentiment pieces – I added the square pieces on the middle inside of the base piece and the smaller rectangular piece to the right hand edge of the middle slider – see photos below.
This card slides open and creates a 3 Dimensional card that can stand on it’s own. Fun, fun, fun! Try this and make some fun stamp art of your own – one stamp at a time!

Happy Stampin’

Natalie