It’s wild to think that you can take a standard card and with two simple cuts you can create a WOW card. Same dimensionals – TOTALLY different results!

The spanner card starts out as a standard card and then something magical happens with two cuts! Stick around and I will show you how to make this fun fold card!

Measurements:
BASE: Pecan Pie CS: 5 1/2″ x 8 1/2″
scored at 4 1/4″
Pecan Pie Two-toned CS: (4) 3/4″ x 5 1/4″
Basic White CS: 3 1/4″ x 4″, 1/2″ x 5 1/2″

Score the card base at 4 1/4″.

Place the right-hand edge of the card at 1″ (on the right-hand side of the cutting track) with the top of the card at the top of the Stampin’ Trimmer upper edge and the score line in the middle.

Place the cutting blade at the score line and cut upwards to the top edge of the card at 1″ in.

Move the card base to the right so that the left-hand edge aligns to the 1″ mark at the left hand side of the cutting track.

Place the cutting blade in the score line and cut upwards to the top of the card base.

Move the left-hand edge to the

Take your four 3/4″ pieces of Two-tone cardstock and emboss two of them on the light side in the 3D Textured Tree Ring embossing folder.

Take the other two strips and stamp the splatter image on the light side in Pecan Pie ink.

Adhere the two stamped strips about 1/8″ in on the inside of the card base leaving 1/8″ even border on the sides and top and bottom of the card. Adhere to both sides of the inside of the card (these strips will be hidden underneath the top flaps when the card is closed.)

Blend the diagonal edges of one of the Basic White 3 1/4″ x 4″ pieces and adhere to the middle of the inside of the card base.

Stamp the inside sentiment in Pecan Pie ink to the center of this inside Basic White layer.

Adhere the two embossed strips of Two-tone CS to the front outside panels leaving an even 1/8″ border on top, bottom and sides.

Using the Stampin’ Positioner because of the large stamp image of the pinecone, take the second Basic White 3 1/4″ x 4″ layer and position the layer under the pinecone stamp in the Stampin’ Positioner.

Add Pecan Pie ink to the stamp and stamp onto the Basic White layer.

Using a water painter wet the brush and drawing from the stamped lines inward draw the ink into the pinecone and stem to watercolor the image.

Using a blender pen, dip the tip into the lid of the Peaceful Pine ink pad with ink on it and use the pen like a colored marker and draw over the pine needle images.

Using blending brushes blend the edges of the pinecone layer with Peaceful Pine and Pecan Pie inks.

Using a White Gel pen I added white lines above the Peaceful Pine marker lines to look like a snow effect!

Adhere the pinecone image layer to the center front panel.

Take the 1/2″ strip and stamp a straight line sentiment across the middle of the strip in Pecan Pie ink.

Blend the edges in Pecan Pie ink and a blending brush.

Add adhesive ONLY 3/4″ in from the outside edges and secure over the two outside panels of the card – this creates a “spanner” piece to connect the two outside panels to act as one unit and “span” the gap leaving the middle panel to become another layer to the card!

This is what the card looks like when you lift the first spanner layer open to reveal layer number 2 which is the card front’s original middle panel!

Adhere three embellishments to the spanner strip and this WOW card is completed!

Try making a spanner card soon with your own stash and see how easy it is to make something special! Now it’s your turn to create some artwork of your very own – one stamp at a time!

Happy Stampin’
Natalie