mixed media pop out fun fold

This is a fun movement card that has two “arms” that swing out from under a DSP covered box.

Measurements:
BASE: Poppy Parade CS: 5 1/2″ x 8 1/2″
scored at 4 1/4″
Piece #1 2 1/2″ x 4 1/2″ score at 1/2″ and 1″
Piece #2 2 1/2″ x 3″
Piece #3 1″ x 3 1/4″ scored at 1/2″, 1″ and 2 3/4″
Pieces #4 and 5 (2) 2 1/4″ x 2 3/8″
Piece #6 1 3/8″ x 7 1/2″ scored
DSP
Piece #1 2 1/4″ x 3 1/4″
Piece #2 2 1/4″ x 2 3/4″
Piece #4 and 5 2 1/8″ x 2 1/4″

Take the 1 3/8″ x 7 1/2″ mechanism and score on the 1 3/8″ side at 1/2″ and 1″
turn on the 7 1/2″ side and score at the 2 1/2″ mark from the top score line to the upper edge and score at the 2 1/2″ mark below the bottom line to the bottom edge.

There are three long sections going down the 7 1/2″ side in the 1 3/8″ x 7 1/2″ layer.
Draw a mark 1/2″ inside the small score line.

Draw a line from the mark to the top of the score line on the narrower strip, then draw another line to the bottom of the score line on the equal strip.

Repeat on the other side.

Score the lines with the Take Your Pick tool.

Cut the four corners from the 1 3/8″ x 7 1/2″ piece.

Fold the scored pieces at the drawn lines.

One side will have an extra flap this will be positioned towards the card front. Bend the score line upwards.

Flip the mechanism over so that the extra flap piece is facing downwards and place glue on the top portion of the mechanism as shown in the photo below.

Place the glue side down on the back of the inside of the card – position the mechanism so it is in the center of the card butting up to the score line.
Close the card front and rub in the middle of the card to secure the glue and bottom of the mechanism to the inside of the card.

The center section of the mechanism should have the tab facing upwards at this point.
Place glue on the back center section – NOT ON THE TAB yet! – above the score line on the mechanism as in the photo below – and close the card front to secure the mechanism to the card front.

The mechanism will be secured on each side of the card and have the front tab free and two arms of the mechanism one off to each side.

Adhere the DSP pieces to the Poppy Parade cardstock pieces:
Adhere the 2 1/4 x 3 1/4 DSP piece to the 2 1/2″ x 4 1/2″ above the score lines.
Adhere the 2 1/4″ x 2 3/4″ DSP piece to the
2 1/2″ X 3″ piece.
Adhere the (2) 2 1/8″ x 2 1/4″ DSP pieces to the 2 1/4″ x 2 3/8″ pieces of cardstock.

Place glue on the left hand arm of the mechanism and position the 2 1/4″ x 2 3/8″ piece with the 2 3/8″ piece along the arm.

Place glue on the right hand arm and glue the 2 3/8″ side of the 2 1/4″ x 2 3/8″ piece to this arm of the mechanism.

Place a thin line of liquid glue to the back edge that is not scored and adhere to the tab on the mechanism.

Fold the mechanism cover at the second score line flatten out the cardstock and place glue on the outer edge and close the card and adhere it to the back portion of the card.
You will need to place the “wings” of the mechanism under the cover before closing the card. This will be the cover for the pop out mechanism!

Take the 1″ x 3 1/4″ cardstock piece and score at 1/2″, 1″ and 2 3/4″

PLace glue on the single tab and place face down in the center of the cover and close the card to secure rubbing over the card to let the glue adhere.

Fold the other side at the second score line and place glue on the first section only. Close the card and secure the cardstock piece to the inside of the card front. It will form a pop up box for the 2 1/2″ x 3″ card stock piece to adhere to.

Place liquid glue to the front of that box.

Lie the 2 1/2″ x 3″ DSP covered piece – face down with the DSP facing down towards the DSP on the cover piece and close the card front and rub on the mechanism to adhere this piece to the upper box.

I stamped two tulip images from the Mixed Florals stamp set and colored them with Poppy Parade, Petal Pink and Granny Apple Green Stampin’ Blends markers and then die cut them.

Now the mechanism and the covers are complete and this is what the card inside will look like.
I cut up one of the tulip images and adhered pieces to the pop out wings of the mechanism so that flowers appear when the pop out is engaged!
I also stamped two sentiments from the Mixed Labels stamp set in Tuxedo Black Memento ink and die cut with the sentiment dies from that set.
I placed the “I’m so glad we’re friends on the inside cover of the mechanism.

I adhered the second tulip image to the outside of the card.

I popped up the other sentiment piece on the card front with Stampin’ Dimensionals.

I added Silver edged sheer ribbon around the card for closure.

I added some of the extra tulip pieces leftover from the inside of the card and popped them up over the ribbon to hold it in place and added Basic Grey and Smoky Slate Pearls to the card to finish it off with a little sparkle!

This is a perfect WOW card for that someone special!
Try this or another one of my fun fold tutorials and go create some artwork of your very own – one stamp at a time.

Happy Stampin’
Natalie